Continuous Microfluidic Antisolvent Crystallization as a Bottom-Up Solution for the Development of Long-Acting Injectable Formulations.

A bottom-up approach was investigated to produce long-acting injectable (LAI) suspension-based formulations to overcome specific limitations of top-down manufacturing methods by tailoring drug characteristics while making the methods more sustainable and cost-efficient. A Secoya microfluidic crystallization technology-based continuous liquid antisolvent crystallization (SCT-CLASC) process was optimized and afterward compared to an earlier developed microchannel reactor-based continuous liquid antisolvent crystallization (MCR-CLASC) setup, using itraconazole (ITZ) as the model drug. After operating parameter optimization and downstream processing (i.e., concentrating the suspensions), stable microsuspensions were generated with a final solid loading of 300 mg ITZ/g suspension. The optimized post-precipitation feed suspension consisted of 40 mg ITZ/g suspension with a drug-to-excipient ratio of 53:1. Compared to the MCR-CLASC setup, where the post-precipitation feed suspensions contained 10 mg ITZ/g suspension and had a drug-to-excipient ratio of 2:1, a higher drug concentration and lower excipient use were successfully achieved to produce LAI microsuspensions using the SCT-CLASC setup. To ensure stability during drug crystallization and storage, the suspensions' quality was monitored for particle size distribution (PSD), solid-state form, and particle morphology. The PSD of the ITZ crystals in suspension was maintained within the target range of 1-10 µm, while the crystals displayed an elongated plate-shaped morphology and the solid state was confirmed to be form I, which is the most thermodynamically stable form of ITZ. In conclusion, this work lays the foundation for the SCT-CLASC process as an energy-efficient, robust, and reproducible bottom-up approach for the manufacture of LAI microsuspensions using ITZ at an industrial scale.

Osmolality of Excipients for Parenteral Formulation Measured by Freezing Point Depression and Vapor Pressure - A Comparative Analysis.

PURPOSE: To investigate the difference in methods to determine the osmolality in solutions of stabilizers used for long-acting injectable suspensions. METHODS: The osmolality was measured by freezing point depression and vapor pressure for 11 different polymers and surfactants (PEG 3350, 4000, 6000, 8000, 20,000, PVP K12, K17 and K30, poloxamer 188, 388 and 407, HPMC E5, Na-CMC, polysorbate 20 and 80, vitamin E-TPGS, phospholipid, DOSS and SDS) in different concentrations. RESULTS: Independently of the measuring method, an increase in osmolality with increasing concentration was observed for all polymers and surfactants, as would be expected due to the physicochemical origin of the osmolality. No correlation was found between the molecular weight of the polymers and the measured osmolality. The osmolality values were different for PVPs, PEGs, and Na-CMC using the two different measurement methods. The values obtained by the freezing point depression method tended to be similar or higher than the ones provided by vapor pressure, overall showing a significant difference in the osmolality measured by the two investigated methods. CONCLUSIONS: For lower osmolality values (e.g. surfactants), the choice of the measuring method was not critical, both the freezing point depression and vapor pressure could be used. However, when the formulations contained higher concentrations of excipients and/or thermosensitive excipients, the data suggests that the vapor pressure method would be more suited.

Impact of Excipients and Seeding on the Solid-State Form Transformation of Indomethacin during Liquid Antisolvent Precipitation.

Long-acting injectables are a unique drug formulation strategy, providing a slow and sustained release of active pharmaceutical ingredients (APIs). In this study, a novel approach that combines liquid antisolvent precipitation with seeding to obtain a stable form of the API indomethacin while achieving the desired particle size distribution is described. It was proven that when a metastable form of indomethacin was initially nucleated, the rate of its transformation to the stable form was influenced by the presence of excipients and seeds (17.10 ± 0.20 µm), decreasing from 48 to 4 h. The final particle size (D50) of the indomethacin suspension produced without seeding was 7.33 ± 0.38 µm, and with seeding, it was 5.61 ± 0.14 µm. Additionally, it was shown that the particle size distribution of the seeds and the time point of seed addition were critical to obtain the desired solid-state form and that excipients played a crucial role during nucleation and polymorphic transformation. This alternative, energy-efficient bottom-up method for the production of drug suspensions with a reduced risk of contamination from milling equipment and fewer processing steps may prove to be comparable in terms of stability and particle size distribution to current industrially accepted top-down approaches.